日本三木联轴器ALS-040ARN-12BHA-19BHA

ALS (R) Type Specifications ALS (R) Types (key/set screw type) ALS (R) Types (clamp types) ALS (R) Types (key/set screw type) [Specifications] Model Torque Misalignment Max. rotation speed ［min-1］ Static torsional stiffness ［N・m/rad］ Radial stiffness ［N/mm］ Moment of inertia ［kg・m2］ Mass ［kg］ Nominal ［N・m］ Max. ［N・m］ Parallel ［mm］ Angular ［°］ Axial ［mm］ ALS-014-R 2 4 0.10 1 0 to ＋0.6 34100 21 380 1.91×10-7 0.007 ALS-020-R 5 10 0.10 1 0 to ＋0.8 23800 43 400 1.08×10-6 0.018 ALS-030-R 12.5 25 0.10 1 0 to ＋1.0 15900 136 650 6.25×10-6 0.047 ALS-040-R 17 34 0.10 1 0 to ＋1.2 11900 1550 1700 3.87×10-5 0.15 ALS-055-R 60 120 0.10 1 0 to ＋1.4 8700 2000 1350 1.66×10-4 0.35 ALS-065-R 160 320 0.10 1 0 to ＋1.5 7400 3100 1400 3.57×10-4 0.51 ALS-080-R 325 650 0.10 1 0 to ＋1.8 6000 6000 1710 1.06×10-3 1.01 ALS-095-R 450 900 0.10 1 －0.5 to ＋2.0 5000 10000 4200 2.24×10-3 1.50 ALS-105-R 525 1050 0.15 1 －0.9 to ＋2.0 4500 12000 5000 3.72×10-3 2.05 *Axial displacement of the ALS-014-R to ALS-080-R is not allowed in the negative direction. *Max. rotation speed does not take into account dynamic balance. *Stiffness values given are from measurements taken at 20℃. *The moment of inertia and mass are measured for the maximum bore diameter. [Dimensions]   Unit ［mm］ Model d1, d2 D L L1, L2 E S C Pilot bore Min. Max. ALS-014-R 3 3 6.5 14 22 7 8 1 3.5 ALS-020-R 4 4 9.6 20 30 10 10 1 5 ALS-030-R 5 6 14 30 35 11 13 1.5 5.5 ALS-040-R 5 8 22 40 66 25 16 2 12.5 ALS-055-R 5 10 28 55 78 30 18 2 15 ALS-065-R 5 14 38 65 90 35 20 2.5 17.5 ALS-080-R 10 19 45 80 114 45 24 3 22.5 ALS-095-R 8 19 55 95 126 50 26 3 25 ALS-105-R 10 19 60 105 140 56 28 3.5 28 *"Pilot bore" refers to center processing. [Standard bore diameter] Unit ［mm］ Model Standard bore diameter d1, d2 ［mm］ 3 4 5 6 6.35 7 8 9 9.525 10 11 12 14 15 16 17 18 19 20 22 24 25 28 30 32 35 38 40 42 45 48 50 55 56 60 ALS-014-R ● ● ● ● ● ALS-020-R ● ● ● ● ● ● ● ● ALS-030-R ● ● ● ● ● ● ● ● ● ● ALS-040-R ● ● ● ● ● ● ● ● ● ● ● ● ● ● ALS-055-R ● ● ● ● ● ● ● ● ● ● ● ● ● ● ALS-065-R ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ALS-080-R ● ● ● ● ● ● ● ● ● ● ● ● ● ALS-095-R ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ALS-105-R ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● *The bore diameters marked with ● are supported as standard bore diameter. *ø11 and below have no keyway; ø12 and above can be processed for old JIS standards, new JIS standards, and new standard motors. [Element]   Unit ［mm］ Model F R1 R2 K A ALS-014-R-EL 6.2 3.5 -- 2.5 1.2 ALS-020-R-EL 8.2 6.2 -- 3.4 1.4 ALS-030-R-EL 10.2 8.5 -- 4 2.2 ALS-040-R-EL 12 18 -- 4.5 3 ALS-055-R-EL 14 24 -- 5.5 3 ALS-065-R-EL 15 30 -- 5.5 4 ALS-080-R-EL 18 37 15 7 4 ALS-095-R-EL 20 43 20 8 4 ALS-105-R-EL 21 50 20 8.5 4 [Standard Hole-drilling Standards]   Unit [mm] Models compliant with the old JIS standard (class 2) JIS B 1301 1959 Models compliant with the new JIS standard (H9) JIS B 1301 1996 Models compliant with the new JIS standard (JS9) JIS B 1301 1996 Models compliant with the motor standard JIS C 4210 2001 Nominal bore diameter Bore diameter [d1・d2] Keyway width [W1・W2] Keyway height [T1・T2] Set screw hole [M] Nominal bore diameter Bore diameter [d1・d2] Keyway width [W1・W2] Keyway height [T1・T2] Set screw hole [M] Nominal bore diameter Bore diameter [d1・d2] Keyway width [W1・W2] Keyway height [T1・T2] Set screw hole [M] Nominal bore diameter Bore diameter [d1・d2] Keyway width [W1・W2] Keyway height [T1・T2] Set screw hole [M] Tolerance H7,H8 Tolerance E9 － － Tolerance H7 Tolerance H9 － － Tolerance H7 Tolerance JS9 － － Tolerance G7,F7 Tolerance H9 － － 3 3+0.0180 － － 1-M3 － － － － － － － － － － － － － － － 4 4+0.0180 － － 2-M3 － － － － － － － － － － － － － － － 5 5+0.0180 － － 2-M3 － － － － － － － － － － － － － － － 6 6+0.0180 － － 2-M4 － － － － － － － － － － － － － － － 6.35 6.35+0.0220 － － 2-M4 － － － － － － － － － － － － － － － 7 7+0.0220 － － 2-M4 － － － － － － － － － － － － － － － 8 8+0.0220 － － 2-M4 － － － － － － － － － － － － － － － 9 9+0.0220 － － 2-M4 － － － － － － － － － － － － － － － 9.525 9.525+0.0220 － － 2-M4 － － － － － － － － － － － － － － － 10 10+0.0220 － － 2-M4 － － － － － － － － － － － － － － － 11 11+0.0180 － － 2-M4 － － － － － － － － － － － － － － － 12 12+0.0180 4+0.050+0.020 13.5+0.30 2-M4 12H 12+0.0180 4+0.0300 13.8+0.30 2-M4 12J 12+0.0180 4±0.0150 13.8+0.30 2-M4 － － － － － 14 14+0.0180 5+0.050+0.020 16.0+0.30 2-M4 14H 14+0.0180 5+0.0300 16.3+0.30 2-M4 14J 14+0.0180 5±0.0150 16.3+0.30 2-M4 14N 14+0.024+0.006 5+0.0300 16.3+0.30 2-M4 15 15+0.0180 5+0.050+0.020 17.0+0.30 2-M4 15H 15+0.0180 5+0.0300 17.3+0.30 2-M4 15J 15+0.0180 5±0.0150 17.3+0.30 2-M4 － － － － － 16 16+0.0180 5+0.050+0.020 18.0+0.30 2-M4 16H 16+0.0180 5+0.0300 18.3+0.30 2-M4 16J 16+0.0180 5±0.0150 18.3+0.30 2-M4 － － － － － 17 17+0.0180 5+0.050+0.020 19.0+0.30 2-M4 17H 17+0.0180 5+0.0300 19.3+0.30 2-M4 17J 17+0.0180 5±0.0150 19.3+0.30 2-M4 － － － － － 18 18+0.0180 5+0.050+0.020 20.0+0.30 2-M4 18H 18+0.0180 6+0.0300 20.8+0.30 2-M5 18J 18+0.0180 6±0.0150 20.8+0.30 2-M5 － － － － － 19 19+0.0210 5+0.050+0.020 21.0+0.30 2-M4 19H 19+0.0210 6+0.0300 21.8+0.30 2-M5 19J 19+0.0210 6±0.0150 21.8+0.30 2-M5 19N 19+0.028+0.007 6+0.0300 21.8+0.30 2-M5 20 20+0.0210 5+0.050+0.020 22.0+0.30 2-M4 20H 20+0.0210 6+0.0300 22.8+0.30 2-M5 20J 20+0.0210 6±0.0150 22.8+0.30 2-M5 － － － － － 22 22+0.0210 7+0.061+0.025 25.0+0.30 2-M6 22H 22+0.0210 6+0.0300 24.8+0.30 2-M5 22J 22+0.0210 6±0.0150 24.8+0.30 2-M5 － － － － － 24 24+0.0210 7+0.061+0.025 27.0+0.30 2-M6 24H 24+0.0210 8+0.0360 27.3+0.30 2-M6 24J 24+0.0210 8±0.0180 27.3+0.30 2-M6 24N 24+0.028+0.007 8+0.0360 27.3+0.30 2-M6 25 25+0.0210 7+0.061+0.025 28.0+0.30 2-M6 25H 25+0.0210 8+0.0360 28.3+0.30 2-M6 25J 25+0.0210 8±0.0180 28.3+0.30 2-M6 － － － － － 28 28+0.0210 7+0.061+0.025 31.0+0.30 2-M6 28H 28+0.0210 8+0.0360 31.3+0.30 2-M6 28J 28+0.0210 8±0.0180 31.3+0.30 2-M6 28N 28+0.028+0.007 8+0.0360 31.3+0.30 2-M6 30 30+0.0210 7+0.061+0.025 33.0+0.30 2-M6 30H 30+0.0210 8+0.0360 33.3+0.30 2-M6 30J 30+0.0210 8±0.0180 33.3+0.30 2-M6 － － － － － 32 32+0.0250 10+0.061+0.025 35.5+0.30 2-M8 32H 32+0.0250 10+0.0360 35.3+0.30 2-M8 32J 32+0.0250 10±0.0180 35.3+0.30 2-M8 － － － － － 35 35+0.0250 10+0.061+0.025 38.5+0.30 2-M8 35H 35+0.0250 10+0.0360 38.3+0.30 2-M8 35J 35+0.0250 10±0.0180 38.3+0.30 2-M8 － － － － － 38 38+0.0250 10+0.061+0.025 41.5+0.30 2-M8 38H 38+0.0250 10+0.0360 41.3+0.30 2-M8 38J 38+0.0250 10±0.0180 41.3+0.30 2-M8 38N 38+0.050+0.025 10+0.0360 41.3+0.30 2-M8 40 40+0.0250 10+0.061+0.025 43.5+0.30 2-M8 40H 40+0.0250 12+0.0430 43.3+0.30 2-M8 40J 40+0.0250 12±0.0215 43.3+0.30 2-M8 － － － － － 42 42+0.0250 12+0.075+0.032 45.5+0.30 2-M8 42H 42+0.0250 12+0.0430 45.3+0.30 2-M8 42J 42+0.0250 12±0.0215 45.3+0.30 2-M8 42N 42+0.050+0.025 12+0.0430 45.3+0.30 2-M8 45 45+0.0250 12+0.075+0.032 48.5+0.30 2-M8 45H 45+0.0250 14+0.0430 48.8+0.30 2-M10 45J 45+0.0250 14±0.0215 48.8+0.30 2-M10 － － － － － 48 48+0.0250 12+0.075+0.032 51.5+0.30 2-M8 48H 48+0.0250 14+0.0430 51.8+0.30 2-M10 48J 48+0.0250 14±0.0215 51.8+0.30 2-M10 48N 48+0.050+0.025 14+0.0430 51.8+0.30 2-M10 50 50+0.0250 12+0.075+0.032 53.5+0.30 2-M8 50H 50+0.0250 14+0.0430 53.8+0.30 2-M10 50J 50+0.0250 14±0.0215 53.8+0.30 2-M10 － － － － － 55 55+0.0300 15+0.075+0.032 60.0+0.30 2-M10 55H 55+0.0300 16+0.0430 59.3+0.30 2-M10 55J 55+0.0300 16±0.0215 59.3+0.30 2-M10 55N 55+0.060+0.030 16+0.0430 59.3+0.30 2-M10 56 56+0.0300 15+0.075+0.032 61.0+0.30 2-M10 56H 56+0.0300 16+0.0430 60.3+0.30 2-M10 56J 56+0.0300 16±0.0215 60.3+0.30 2-M10 － － － － － 60 60+0.0300 15+0.075+0.032 65.0+0.30 2-M10 60H 60+0.0300 18+0.0430 64.4+0.30 2-M10 60J 60+0.0300 18±0.0215 64.4+0.30 2-M10 60N 60+0.060+0.030 18+0.0430 64.4+0.30 2-M10 *All standards starting from ø11 are the same as those in the old JIS standards column. *For ALS-014, set screw size is M3. *Positions of set screws and keyways are not on the same plane. *Set screws are included with the product. *Positioning precision for keyway milling is determined by sight. *Contact Miki Pulley when the keyway requires a positioning precision for a particular flange hub. *Consult the technical documentation at the end of this volume for standard dimensions for bore drilling other than those given here. [Set screw position] Unit [mm] Model Distance C from edge［mm］ ALS-014 3.5 ALS-020 5 ALS-030 5.5 ALS-040 12.5 ALS-055 15 ALS-065 17.5 ALS-080 22.5 ALS-095 25 ALS-105 28   ALS (R) Types (clamp types) [Specifications] Unit ［mm］ Model Misalignment Max. rotation speed ［min-1］ Static torsional stiffness ［N・m/rad］ Radial stiffness ［N/mm］ Moment of inertia ［kg・m2］ Mass ［kg］ Parallel ［mm］ Angular ［°］ Axial ［mm］ ALS-014-R 0.1 1 0 to ＋0.6 10000 21 380 1.98×10-7 0.007 ALS-020-R 0.1 1 0 to ＋0.8 10000 43 400 1.09×10-6 0.019 ALS-030-R 0.1 1 0 to ＋1.0 10000 136 650 6.19×10-6 0.045 ALS-040-R 0.1 1 0 to ＋1.2 10000 1550 1700 4.01×10-5 0.16 ALS-055-R 0.1 1 0 to ＋1.4 7000 2000 1350 1.63×10-4 0.34 ALS-065-R 0.1 1 0 to ＋1.5 5900 3100 1400 3.69×10-4 0.54 ALS-080-R 0.1 1 0 to ＋1.8 4800 6000 1710 1.04×10-3 1.00 *Axial displacement is not allowed in the negative direction. *Max. rotation speed does not take into account dynamic balance. *Stiffness values given are from measurements taken at 20℃. *The moment of inertia and mass are measured for the maximum bore diameter. [Dimensions]   Unit ［mm］ Model d1, d2 D DB L L1, L2 E S B G M Tightening torque ［N・m］ Min. Max. ALS-014-R 3 6 14 16.1 22 7 8 1 3.5 4.8 1-M2 0.4 ALS-020-R 4 8 20 20 30 10 10 1 5 6.5 1-M2.5 1 ALS-030-R 6 14 30 30 35 11 13 1.5 5.5 10.5 1-M3 1.5 ALS-040-R 8 20 40 43.2 66 25 16 2 12.5 15 1-M5 7 ALS-055-R 10 28 55 55 78 30 18 2 10.5 20 1-M6 14 ALS-065-R 14 35 65 69.8 90 35 20 2.5 11.5 24.5 1-M8 30 ALS-080-R 19 45 80 80 114 45 24 3 11.5 30 1-M8 30 *The øDB value is measured assuming that the head of the clamping bolt is larger than the external diameter of the hub. *The nominal diameter for the clamping bolt M is equal to the quantity minus the nominal diameter of the screw threads, where the quantity is for a hub on one side. Standard bore diameter and allowable transmission torque Model Standard bore diameters d1, d2 ［mm］ and rated transmission torque ［N・m］ 3 4 5 6 6.35 7 8 9 9.525 10 11 12 14 15 16 18 19 20 22 24 25 28 30 32 35 38 40 42 45 ALS-014-R 0.31 0.42 0.54 0.65 ALS-020-R 1.2 1.6 2.1 2.2 2.6 3 ALS-030-R 2 2.2 2.7 3.4 4 4.4 4.7 5.4 6 7.4 ALS-040-R 8 12 14 16 19 23 31 34 34 34 34 34 ALS-055-R 21 25 28 35 38 41 48 51 54 61 67 71 80 ALS-065-R 40 44 47 54 58 61 68 75 79 89 96 103 114 ALS-080-R 53 59 72 84 90 108 121 133 151 170 182 194 212 *Bore diameters whose fields contain numbers are supported as the standard bore diameters. *Bore diameters whose fields contain numbers are restricted in their rated transmission torque by the holding power of the shaft connection component. The numbers indicate the rated transmission torque value [N·m]. * The recommended processing tolerance for paired mounting shafts is the h7 class. However, for a bore diameter of ø35, the shaft tolerance is -0.025 to +0.010 *Bore diameters between the minimum and maximums shown in the dimensions table are compatible, but bore diameters other than those shown in the above table require other arrangements. Contact Miki Pulley for details.   本公司坐落在中国经济特区、全国性经济中心城市和国际化城市--深圳，本公司有着十几年丰富的经验，一直本着兢兢业业的态度做事，诚诚恳恳的态度做人的经营理念，在质量上严格把控，在服务上热情耐心，广交各方好友，欢迎您随时联系或来实地查看！！ 公司原厂直销，货期短，无中间环节,价格更有优势，品质更有保证！！ 感谢您关注的产品，如以下图片和型号不符请联系咨询，谢谢！